If you’re a mountain bike enthusiast, you know that a flat tire or a busted wheel can turn your adventure into a nightmare. Knowing how to put on a back wheel on a mountain bike is an essential skill that every rider should have in their arsenal. This step-by-step guide will take you through the process, so you can get back on the trail without missing a beat.
Before we dive into the nitty-gritty, it’s essential to understand the anatomy of a mountain bike’s rear wheel. A back wheel typically comprises a hub, spokes, a rim, and a tire. The hub houses the bearings that allow the wheel to rotate, and spokes connect the rim to the hub. The rim is where the tire sits, and it’s responsible for providing a secure mounting surface for the tire. Keep this in mind as we navigate through the step-by-step process of mounting a back wheel.
Gather the necessary tools and materials
Before diving into the process of changing your back wheel, it is important to make sure that you have all the necessary tools and materials. Here’s a quick checklist to help you get started:
1. Wrenches: You’ll need a set of wrenches, including a 15mm wrench that will help you remove the axle nuts.
2. New wheel: A quick-release or bolt-on wheel will do the trick, depending on your bike’s specifications.
3. Inner tube: Carry an extra inner tube for flat tires.
4. Tire levers: You’ll need these to remove the tire from the rim.
5. Pliers: You may need a pair of pliers to hold the axle in place.
Once you have all the tools and materials, you’re ready to move to the next step – removing the old wheel. Make sure to keep all the small parts in a safe place to avoid losing them.
Read Also: Best Mountain Bike Helmets Under $50: Safety and Style on a Budget
Remove the old back wheel
Removing the old back wheel is essential before you can put on a new one. To start, shift your bike chain to the smallest chainring and the smallest cog. This will loosen the chain and make it easier to remove the wheel. Next, use a quick-release lever, which is typically located on the left side of the wheel hub. Open the lever and carefully lift the bike off the ground using the frame or seat.
Once the wheel is off the ground, hold onto the tire and gently pull it away from the frame. Make sure to hold onto the wheel so that it doesn’t fall off and cause damage to the bike or yourself. Once the wheel is removed, be sure to examine it closely for any damage or wear and tear. If there is any damage, it may be a good idea to replace the entire wheel rather than attempting to repair it. With the old wheel removed, you can now move onto installing the new wheel.
Inspect the bike frame and wheel components
Before putting on the back wheel of your mountain bike, it is essential to inspect the bike frame and the wheel components. These components must be in good condition to ensure optimal performance and safety. Start by checking the bike frame visually for any cracks or bends; this is a critical step as riding with a damaged frame can lead to serious accidents.
Next, inspect the wheel components, such as the axle, spokes, and rim, for any damages. The axle should be straight and have no signs of damage, bends, or rust. Check the spokes to ensure they are firmly in place and not bent. Bend spokes can lead to imbalances in the wheel, making it challenging to ride. Lastly, check the rim for any damages, such as dents, warps, or cracks, as this can cause the wheel to wobble and affect the balance of the bike. Having verified all these components are in good condition, you can proceed to the next step of putting on the wheel.
You may also like: How to Easily Replace a Mountain Bike Inner Tube
Install the new back wheel
Once you have removed the old back wheel, it is time to install the new one. Begin by aligning the chain and cassette with the freehub. Ensure that the quick-release skewer is in the open position and remove any protective caps from the axle.
Now, place the new back wheel into the frame, making sure the axle is fully seated in the dropouts. Tighten the quick-release lever to secure the wheel in place. Use caution not to overtighten the skewer, as this can damage the bearings or frame. Finally, check that the wheel is straight and centered by spinning it and making sure it does not rub against the brake pads or frame. Once everything is in order, take your bike for a test ride to ensure everything is working correctly.
Adjust the derailleur and chain
Once you’ve successfully installed the back wheel onto your mountain bike, it’s time to adjust the derailleur and chain. A well-tuned derailleur will ensure that your chain moves smoothly from gear to gear, allowing for an efficient and effective ride. To begin, shift your bike into the highest gear and check that the derailleur pulley is aligned directly beneath the smallest cog on the cassette. Next, use the barrel adjuster to fine-tune the shift cable tension, making sure that each shift moves cleanly and crisply between gears.
Additionally, the chain may require some adjustments after installing the back wheel. Start by checking the chain tension – it should be tight enough that it doesn’t sag, but not too tight that it restricts turning the pedals. Use the rear derailleur and gears to check the chain’s tension as you turn the pedals, making sure that they move smoothly without skipping or jumping. A well-adjusted derailleur and chain will ensure that your mountain bike runs smoothly and efficiently on the trails.
Inflate the tire and test the bike
Inflate the tire and test the bike
Once the back wheel is securely in place, it’s time to inflate the tire. Attach the pump to the valve and begin pumping. Make sure to check the recommended PSI for your specific tire and adjust accordingly. Overinflating can cause the tire to explode, while underinflating can make the ride bumpy and unstable. Once you reach the desired PSI, remove the pump and screw the valve cap back on.
Now that the tire is inflated, it’s time to test the bike. Double-check that everything is properly tightened and adjusted before hopping on. Take a short ride to make sure everything feels secure and smooth. Test the brakes to ensure they are working properly. If anything feels off, stop and make any necessary adjustments before continuing. With the back wheel properly installed and checked, your mountain bike is ready to take on any trail.
Related Post: How to Set Up Your Full Suspension Mountain Bike for Maximum Performance
Tips for maintaining your back wheel and ensuring a smooth ride
Maintaining your back wheel is crucial for ensuring a smooth and safe ride on your mountain bike. There are several tips you can follow to take care of your wheel and prevent any future issues.
Firstly, it is important to regularly check the tire pressure and ensure it is at the recommended level. This helps to avoid punctures and improves control on the trails. Secondly, keep an eye on the spokes and make sure they are tight and straight. Loose spokes can cause the wheel to wobble, which can lead to instability and damage over time. Finally, clean and lubricate your chain frequently to prevent wear and tear on the gears. By following these simple tips, you can extend the life of your back wheel and enjoy a smooth ride on your mountain bike for longer.
Wrapping Up
In conclusion, it’s important to be careful when replacing or putting on a back wheel on a mountain bike. This can be a challenging task, but patience and attention to detail can make all the difference. Starting by selecting the right wheel and ensuring the axle is properly aligned can help to avoid potential issues down the road.
Remember to double-check the tightness of all bolts and consult a professional if you aren’t comfortable with any part of the process. With a bit of practice, you’ll be able to put on a back wheel like a pro and get back to enjoying the great outdoors on your mountain bike.